How to make a partition?

Now in the construction of largea variety of useful devices that make it easier for men to perform repairs themselves. In our time, you can not have a professional education, that would know how to make a partition in your apartment or house. And it is not necessary to invite professionals (who may not be professionals at all), you can do this yourself. In this article you will find all the necessary information on the issue of partitions in the room. Recommendations for the choice of materials and the organization of work.

How to make a plasterboard partition

In order to make this partition, you should have such materials: drywall, metal knife, gloves, tape measure, electric drill.

The first thing we need to do is to mount the frame. This is a quick procedure even for an inexperienced master. Based on where the frame will be fastened, we mark out the place where our wall will be located. After that, using the levels, we transfer these marks to the ceiling. To quickly screw the profile and strengthen the plates, use special screws (quickly screwed). After you have made a frame, on the one hand start to cover it with a sheet. Watch for screwing the screw, its bonnet should be parallel with the surface of your plates, otherwise the appearance will not be presentable. Then fill in the voids. This is done with the help of thermal insulation material. This will not allow extraneous noise to freely enter the room. Work with gloves if you use a special cotton wool, and after the filling of voids, close the septum on the other side.

Preparing for finishing

The first thing you need to do is to primeryour gypsum board, then shpaklyuem hats screwed screws, joints of plates, too, shpaklyuem. Only after that you can paint or crate the wallpaper on top of your septum, or lay the tile.

How to make a partition in a room of glass blocks

If you use material for partitions, suchas glass blocks, you will make not only functional improvement of the room, but also decorative. Also, because of their nature, glass blocks will let in light and therefore your room will never be dark. This material can be of different texture, color, different size, so you quickly find a suitable glass for your room.

If we consider the habitual to our eyeglass blocks, they are nineteen by nineteen in length, and by a width of seven and a half by ten centimeters. Their external appearance resembles a tight glass of different colors. This material is convenient because it lets a lot of light into the room (up to eighty percent and, you see, it's not enough!). As for sounds, this material adequately soundproofs your room.

How to make an internal partition ofglass blocks? Before laying glass blocks, you must make a screed and plaster. These heavy blocks must be laid in the same way as the brick is laid. Pay attention to the work with the thickness of the seams - it must necessarily be the same. If you do a different thickness, then your "work of art" will look untidy. It can be adjusted if you use rails. Lay them along the edges of the glass block. There they should be until the end, that is until the solution will not solidify. After the masonry is made and the cement is dry, you do the basting. You do it qualitatively, otherwise the appearance of your partition will not be aesthetic.

How to make a partition wall made of bricks

Brick partition is spread only ondense and strong base: reinforced concrete slabs or concrete. You should understand that such a partition, albeit of high quality, is also very weighty. So we do not recommend doing it on high floors in wooden or old houses, since it can lead to undesirable consequences. You can make a partition not only from the usual brick, but from the shell, foam block or gas block. It all depends on your skills and financial capabilities.

Choose a high brand of brick no lower than M25. If you put the partition in half a brick, and not in a whole, then this is the most acceptable option for a living room. The width of the rib will be approximately six and a half centimeters. If you have a thin double construction, then necessarily reinforce it with a wire. If you do a double laying, then you can lay communications in it. But the pipes should always be protected with insulation if they pass between you and the partition in the partition.

If you use not brick, but aerated concrete,foam concrete, shell, you will make less load on the base itself, plus everything else and increase the sound insulation. Such a construction should not be wide (no more than 15 centimeters). Another plus: on such a wall it is easier to apply various materials for plaster.

Starting the masonry

If you use a brick, mixcement-sand mortar, this solution is suitable for laying shell rock. If you make a wall from a foam block and similar materials, then take better special solutions. They are sold in any construction shop. Row first lay out only on a thick layer of mortar. If your baffle is long and tall, then build the reinforcement every four or five rows. It is better to place the wire or grid not only between the rows of masonry, but also to fix it in the existing walls. Use the level to ensure that your masonry is level.

Bricks and other materials (shell rock, foam,Aerated concrete) must be protected from any moisture. So you have to treat the room with waterproofing. Wet cleaning is also not recommended. After you have laid out your septum, treat it with water-repellent materials.

Final work

The resulting wall must be plastered, betterUse a special plaster where the gypsum is based. With such materials it is easier to work and they are better for the room itself. Use only non-rusting materials in the plaster grid, otherwise it may rust after plastering and will appear ugly on the wall itself.

Before plastering, prepare a wall: clean off dirt, dust, other contaminants. After that, dilate the seams. But it is worth noting that for finishing work with a brick partition, you should wait at least two to three weeks. So the masonry dries up completely. If you do not understand something, there are more than one video on the Internet about how to make a partition with your own hands.

How to make a wooden partition

For wood partitions, purchase boardsedged or sheeted, the thickness of which should not exceed five centimeters, and the width of twenty. The boards should not reach the ceiling by about a centimeter, a maximum of two, since the wall will bend, if the house is new and requires shrinkage.

Take a plumb line and draw a vertical strip on theThe wall adjoining the former partition. Fix the markings: on the floor and ceiling ninety degrees from the wall. Then we beat the bars to the ceiling and the wall. Then insert into the resulting grooves, cooked boards. Next you act, given the advice given above. In fact, everything is very simple. This version of the partition is the easiest and less laborious.

Now you have to make a decision, from which it is better to make partitions in your home. We wish you good works!

Related news

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition

How to make a partition